• Chamber Dimensions(WxLxH): approx 33 c m x 38 cm x 25cm
• Number of knives: Approx 18 or to suit customer needs
• Knife Thickness: Approx 18mm or to suit customer needs
• Knife Diameter: Approx 16cm or to suit customer needs
• Tecth per Knife : minimum 3
• Number of Shafts: 2 ie double shaft shredder

Drive of the shredder:

• Must be motor driven
• Motor Horsepower : approx, 10 HP
• Motor RPM: minimum 1750
• Speed Reduction: 60:1
• Generated Torque; min 40 Nm or 350 lbs/in
• Gearbox: should be parallel shaft
• Shock protection: Rubber mount torque arm
• Power : 220vac, 1ph or 400 VAC, 3 ph or suit customer needs

Ancillaries to be included:

• Sherdder stand, fabricated from 3” sq. steel tube, standard height 30 inches
• Shredder hopper , fabricated form 16 gauge steel, with optional switched hopper lid.

(E) Features & Technical Specification of Conveyer:

To carry processed waste from vessel to shredder

Control:

• Motor starter overload protection
• Control housing Nema Type 12
• Safety pull stops along both sides of conveyor

Ancillaries:

• Conveyor stand , fabricated from 2” sq. steel tube
• Raised sidewalls fabricated form 16 gauge steel

dimension:

• Over-all length: between 20-25 feet or appropriate length depending on the installation requirement.
• Over-all width: between 24-30 inch
• over-all (without including stand) : between 12-14 inch
• Available inclines: 0-40 degrees

Belt:

• Belt Speed: 75 fi/min
• Dam spacing; approx, 16 inch

Drive:

• Motor driven
• Horsepower: Approx .075
• Motor RPM: approx.60
• Electrical power input: 220 vac. 1ph or 400 VAC, 3 ph or to suit customer needs.

(F) Technical Specification of tipper features:

• It is to be designed to allow for easy bin positioning under the door to unload processed waste and easy

inaneuverapility for lifting and tipping the waste into the shredder hopper.

• Equipment with 2 bins to accommodate processed waste loads to be loaded into the shredder and shredded waste to be

transported to the disposal bin.

• Frame: Rugged heavy duty frame constructed of formed and welded steel formed and welded steel for extra strength.
• Mast: Fabricated with channel steel for greater strength and dependability. Open structure design complete with

safety cage to offer greater visibility

• Lifting Chains: Must be dual lifting chain of roller style & must meet safety factor at least 6:1
• Hydraulic system: durable cylinder with a chrome plated ram and a relief valve for overload protection
• Forks: Heavy duty approx 4.0” wide x 42” long fixed forks.
• Platform; solid steel
• Battery: A heavy duty 12 volt, 125 amps/hour industrial strength battery.
• Overload protection plugs into any 220 VAC outlet.
• Steering: A pallet truck style steer handle for steering and approx. 4” phenolic wheels with roller bearings located

in the straddle legs.

• Brake: A hand controlled floor lock brake that secures the unit in place.

Specifications:

• Load capacity; Approx 1500 lbs
• load centre: Approx 24 inch
• Raised fork height: to suit customer needs
• Overall must height: to suit customer needs
• Lowered height: minimum 4.0 inch
• Fixed fork width: approx 7 inch
• Fork length : approx 42 inch
• Platform of approx.25”x25”
• overall width approx 25 inch
• castors: approx 5 inch phenolic
• Front wheel : approx 4 inch phenolic